search
banner

What’s the maintenance and assembly methods of koyo water pump bearings?

1,101 Published by admin1 Apr 15,2019

The automobile koyo water pump bearings is a bearing. The cage material is usually made of reinforced nylon 66. The material of the sealing ring is generally made of nitrile rubber. When the requirements are high, the fluorine rubber sealing ring can also be used.

Prevention of assembly of foreign bodies
When the imported koyo water pump bearings are dynamically balanced on the rotor, it is easy to put the iron filings generated during the dynamic balance into the inside of the imported bearings. Therefore, it is better to do the dynamic balancing before loading the imported koyo water pump bearings. Some manufacturers are convenient for assembly.

koyo water pump bearings

When assembling, apply some oil or grease to the imported koyo water pump bearings chamber to lubricate the effect. But it is often difficult for the operator to control the amount. If the oil or grease accumulates more in the imported bearing housing? Even when the inlet bearing rotates, it is easy to enter the inside of the inlet koyo water pump bearings along the shaft. It is best not to apply oil or grease to the imported koyo water pump bearings chamber. If it is not coated, it must be controlled and not accumulated in the imported bearing chamber.

Prevention of paint rust
The characteristic of paint rust is that it is mostly in the sealed motor. The motor sounds very well when assembled. But after some time has been put in the warehouse, the abnormal noise of the motor is greatly removed. The pump shaft is connected to the koyo water pump bearings. Rusty phenomenon. In the past, many manufacturers thought that it was a problem of importing koyo water pump bearings. After our constant publicity. The motor factory has realized that it is mainly a problem of insulating varnish. This problem is mainly caused by the acidic substance volatilized by the insulating paint forming a corrosive substance under a certain temperature and humidity. Corrosion of the inlet koyo water pump bearings leads to damage of the imported bearing. This problem can only be achieved by using a good insulating varnish and ventilating it for a period of time after drying.

original koyo water pump bearings

Selection and control of shaft and inlet bearing chamber tolerances
The pump shaft and the imported bearing should be rotated to the flexible and unblocked feeling after being pressed into the imported koyo water pump bearings. If the obvious rotation is not flexible, it means that the size of the shaft is too large and the tolerance should be lowered. For example, if the pump shaft is pressed into the shaft and the shaft is rotated by hand, there is a clear “sand” feeling. The tolerance of the shaft is too large or the roundness of the shaft is not good. Therefore, it is necessary to control the roundness when controlling the tolerance of the shaft and the koyo water pump bearings chamber. Many domestic manufacturers only control the tolerance and do not control the roundness.

in stock koyo water pump bearings

Assembly method of imported koyo water pump bearings
Because the imported koyo water pump bearings are high-precision products, the pump shaft couplings are easily damaged due to improper assembly of the pump shaft and the imported bearing channel. When the imported bearings are assembled, there should be a special mold that cannot be knocked at will. When pressing the shaft, only a small circle is required. When the large circle is pressed, only a large circle of force is applied. It is required to use air pressure or hydraulic pressure during assembly. When the press is installed, the upper and lower touches should be outside the horizontal state. If it is tilted, the inlet bearing channel will be damaged due to the force, and the imported bearing will produce a sound.

If you need koyo water pump bearings or other bearings, please contact me any time!

Contact: Ellen
Email: iko@zyslbearing.com
Skype: +8618668909563
MP/Whatsapp: +8618668909563
Wechat:18668909563

 

How to remove and install radial spherical bearings?

How to remove and install radial spherical bearings? The following information show you the metho...

Do you like ? 903

Read more

What is the structure of the slewing plummer blocks?

The slewing plummer blocks is a large and extra large bearing housing that can accept comprehensi...

Do you like ? 1,037

Read more

How to adjust the installation clearance of self roller bearings?

Self roller bearings have double row rollers, the outer ring has one shared spherical raceway, an...

Do you like ? 1,018

Read more

How to choose the suitable ball bearing units from different designs?

According to the different requirements of the bearing and ball bearing units, the classification...

Do you like ? 973

Read more

Features of all balls bearings

Common equipment using all balls bearings are: motor shafts, transmission parts for light (civil)...

Do you like ? 1,026

Read more

What is the effect of high temperature on imperial ball bearings?

High temperature impact on imperial ball bearings If the lubrication or installation is not appro...

Do you like ? 1,030

Read more

ZYSL factory making ball bearings with customers’ customized specifications.

ZYSL factory making ball bearings with customers’ customized specifications.Our company has...

Do you like ? 1,070

Read more

These problems should be noticed on the using of radial thrust bearing.

Radial thrust bearing is divided into thrust ball bearing and thrust roller bearing. Radial thrus...

Do you like ? 1,140

Read more