search
banner

Regular lubrication and maintenance of NTN Roller Bearings

913 Published by Sep 30,2018

After the NTN Roller Bearings is installed in the main machine, if the radial runout of the roller bearing main shaft is measured, it can be found that the measured value of each revolution has a certain change; when the measurement is continuously performed, it can be found that after a certain number of revolutions, this Changes will repeat approximately. The index for measuring the degree of such change is the cyclic rotation precision, and the change approximately repeats the required number of revolutions to represent the "quasi-period" of the cycle rotation accuracy. The magnitude of the magnitude change in the quasi-period is large, that is, the cycle rotation precision is poor. 

NTN Roller Bearings original

1, grease lubrication

Relubrication of NTN Roller Bearings is best carried out during planned equipment downtime and is periodically replenished, while removing old grease or extruding old grease through the drain. Wipe the grease fitting clean before adding fresh grease. If the bearing housing does not have a grease fitting, the bearing housing cover or end cap should be opened to remove the old grease and, after cleaning, replenish the same type of fresh grease.

NTN Roller Bearings in stock

2, lubricating oil lubrication

Regularly check the oil level and oil quality of the lubricating oil. Under normal circumstances, the normal oil level should be within the range of 1/3-2/3 of the equipment oil level window or mark. The oil filling method is oil cup, the oil level shown only represents the oil replenishing capacity, and the bearing tank oil level is to meet the operation requirements. The oil level in the oil cup is less than 1/4 of its total volume.

NTN Roller Bearings Japan

Check and replenish the oil method, take a small amount of lubricating oil as a sample and compare it with fresh oil. The competent unit can consider the oil quality test to ensure the oil quality is qualified. If the sample looks cloudy, it may be the result of mixing with water, which is often referred to as oil emulsification. At this point, the lubricant should be replaced. Installation of the fixed-end front bearing on the shaft: Thoroughly clean the tapered roller bearing with clean cleaning kerosene. For grease lubrication, firstly inject the organic solvent containing 3% to 5% grease into the ntn bearing for degreasing and cleaning. Use a grease gun to fill the bearing with a certain amount of grease (10% to 15% of the bearing space volume); heat the NTN Roller Bearings to raise the temperature by 20 to 30 °C, load the bearing into the shaft end with a hydraulic press; press the adapter sleeve on the shaft And axially position the bearing end face with appropriate pressure; wind the belt of the spring balance on the outer ring of the bearing, and check whether the specified preload has a large change by measuring the starting torque (even if the taper roll The sub-bearings are correct, but the preload is also subject to change due to the deformation of the fit or cage.

If you need NTN Roller Bearings or other bearings, please contact me any time!

Contact: Ellen
Email: iko@zyslbearing.com
Skype: +8618668909563
MP/Whatsapp: +8618668909563
Wechat:18668909563

How to remove and install radial spherical bearings?

How to remove and install radial spherical bearings? The following information show you the metho...

Do you like ? 1,755

Read more

What is the structure of the slewing plummer blocks?

The slewing plummer blocks is a large and extra large bearing housing that can accept comprehensi...

Do you like ? 1,771

Read more

How to adjust the installation clearance of self roller bearings?

Self roller bearings have double row rollers, the outer ring has one shared spherical raceway, an...

Do you like ? 1,595

Read more

How to choose the suitable ball bearing units from different designs?

According to the different requirements of the bearing and ball bearing units, the classification...

Do you like ? 1,877

Read more

Features of all balls bearings

Common equipment using all balls bearings are: motor shafts, transmission parts for light (civil)...

Do you like ? 1,558

Read more

What is the effect of high temperature on imperial ball bearings?

High temperature impact on imperial ball bearings If the lubrication or installation is not appro...

Do you like ? 1,518

Read more

ZYSL factory making ball bearings with customers’ customized specifications.

ZYSL factory making ball bearings with customers' customized specifications.Our company has more ...

Do you like ? 2,188

Read more

These problems should be noticed on the using of radial thrust bearing.

Radial thrust bearing is divided into thrust ball bearing and thrust roller bearing. Radial thrus...

Do you like ? 1,689

Read more