search
banner

Do you know what a dental bearing is?

2,410 Published by May 20,2020

What is a dental bearing? Few people may know such a bearing, and the general dentist may know more, because dental drill bearings are mainly used for dental dentist mobile phone special bearings. Based on the understanding of dental drill bearings, share the following relevant information.

What is a dental bearing?
There is a key component on the dentist's mobile phone, called the high-speed dental drill component. The high-speed turbo dental drill mobile phone bearing is a mechanical bearing composed of shafts, worm gears, spring chucks, spring gaskets, back covers, housings, rolling bearings, rubber positioning rings and other parts. The rolling bearings used are called dental bearing. The turbine, the bearing and the shaft have an interference fit, and the compressed air drives the whole high-speed rotation to drive the spring chuck and drill bit installed in the shaft hole to work.

dental bearing

dental bearing material performance characteristics

1. The bearing material is critical to its accuracy, performance and life. The high-speed turbine dental drill mobile phone bearing ring material should use special anti-corrosion stainless steel, the material of the ball should be Si3N4 ceramic ball with small thermal expansion coefficient, and the material of the cage should be polyimide TORLON which is resistant to compression, impact and high temperature.

2. Strict bearing processing technology is the key to product success.The bearing ring processing technology should be optimized according to the structural characteristics and technical requirements of high-speed dental drill bearings, and the reasonable process retention, dust-proof structure and key characteristic parameters should be determined. A solid crown-shaped cage formed by lathe processing.

in stock dental bearing

dental bearing installation and maintenance

When the dental bearing is installed, the interference between the bearing internal control and the shaft is best at 0 ~ 2μm. The circular deviation of the shaft should be less than 2μm. The force of pressing the shaft into the inner hole of the bearing should directly act on the inner ring of the miniature bearing, and must not pass the action of the steel ball or the ring groove of the ring, so as not to damage the bearing accuracy. After installing a pair of bearings on the turbine, the turbine and bearings must be cleaned and dripped into the lubricating oil before installation into the machine head (acetone or ethanol cannot be used for the cleaning fluid). When inserting the dental drill bearing into the machine head, a certain axial preload (size 1 ~ 2N) should be applied to a pair of bearings to obtain the ideal high-speed performance.

original dental bearing

After the installation of the dental bearing is completed, check that the shaft can not have axial series motion and the bearing rotates flexibly. If the axial preload is too tight or too loose, you should replace the washer or increase or decrease the gasket to ensure the correct preload after the dental bearing is installed, to prevent the dental bearing from slipping or spinning during high-speed operation. The normal operation and service life of dental bearing are closely related to the maintenance of the turbine head. In the clinical use of high-speed dental drills, the turbine head must be cleaned and maintained every day. Before use, the turbine head should be removed and added with cleaning fluid, and then fixed by hand to keep the drill fixed and not turned. Pass compressed air for a few seconds to clean and lubricate before use.

Welcome to contact me to get the price of dental bearing!

Contact: Ellen
Email: [email protected]
Skype: +8618668909563
MP/Whatsapp: +8618668909563
Wechat:18668909563

 

How to install the double row angular contact ball bearing?

Double row angular contact ball bearing installation is more complex than deep groove ball bearin...

Do you like ? 4,790

Read more

The cause of micro miniature bearing failure and the solution to overheating of temperature.

Failure reason of micro miniature bearing About 40% of the failure of micro miniature bearings i...

Do you like ? 1,684

Read more

Six Mistakes in the Replacement of skate shoes ceramic bearing by Novices

Novice Mistakes 1: Do not consider the characteristics of your own actions, blindly choose Althou...

Do you like ? 1,609

Read more

CNC machine bearings common quality problems and main causes.

When assembling cnc machine bearings, the Venus machine tool must be preloaded, so that the origi...

Do you like ? 2,221

Read more

the performance and feature of stainless steel self-aligning ball bearing

Performance characteristics of stainless steel self-aligning ball bearing Self-aligning ball bear...

Do you like ? 1,694

Read more

How to choose the suitable longboard skateboard wheels?

The long board has a strong sense of operation and is quick to get started. The longboard is a mu...

Do you like ? 1,587

Read more

What’s the design and installation of tapered thrust bearing?

The tapered thrust bearing with cage is a split design so that the two washers as well as the rol...

Do you like ? 1,981

Read more

the disassembly, installation and operating environment of tapered needle bearing

Disassembly of the tapered needle bearing: When the bearing is to be used continuously after it i...

Do you like ? 1,437

Read more